The Co Pilot for the 06-07 Allison 1000 makes it possible to transfer increased power levels over stock developed by a modified engine to the rear wheels without causing the dreaded transmission slip and condition that plagues the Allison transmission.
The Co-Pilot package alone, without any internal transmission modifications, allows the transmission to handle approximately 85 more horsepower and 120 foot pounds of torque over the power level at which the stock Allison will typically enter into "Fail Safe" mode, roughly 425HP/650Tq. The Co-Pilot kit allows the transmissions clutch packs to receive full line pressure (clamping force needed to apply clutches) during high power situations. The stock Allison LCT-1000/2000 and 2400 transmissions torque capacity has been reduced by the limited pressure that is available i the clutch packs. The stock Allison transmission only receives approximately 86-PSI oil pressure to the clutch packs when in 5th gear. After the addition of the Co-Pilot transmission system the transmission clutch packs receive approximately 230-PSI, more than 2.5 times the stock pressure.
FEATURES & BENEFITS:
The biggest factor that causes transmission failures, as noted before, is the fact that apply pressures are too low. They work great for a stock transmission, however, as soon as more power is added, damage is likely to occur. The Trans go shift kit has been used for years with great success, but how successful is it really? The trans go will raise your apply pressure to about 15-PSI or so over stock. This equates to somewhere around 100-PSI. This is a miniscule amount when compared to the ATS Co-Pilot. The common misconception is that it will cause far too much pressure if the Co-Pilot and Trans go are used in tandem. This is false. The only modification is that when drilling the separator plate, it is ideal to only drill out about 65/1000 instead of 100/1000. With these two enhancements used together, a stock Allison will see probably see a 1:1 ratio of line pressure to apply pressure. This will yield incredible results in a stock transmission.
It is often said that timing is everything, and that adage holds true in this scenario. The stock transmission has a very gradual pressure ramp up time, which is another cause of slipping under higher power levels. The Trans go follows the same pressure ramp up time, because it is mechanical, it is simply imitating with magnification of the stock attributes. The Co-Pilot however is electronic and programmed by ATS. We enabled it to bring the pressure up in a fraction of the time, allowing for a greater amount of shock force and clutch grip.
By allowing the available line pressure to the clutch packs, we have designed a system that increases the torque capacity of the stock Allison transmission by over 280 foot pounds of torque with the simple addition of our Co-pilotTM transmission kit. This increased pressure is only applied during high engine torque output, unlike other mechanical kits that do not use electronic controls. This removes the concern of excessive pressure on vital transmission parts such as delivery rings, drums, shafts, etc. during normal operation. Other valve body kits being sold today perform this hydraulically, only after the trim valve has completed the shift. The problems with these hydraulic kits lie in two areas. The first is the lack of ability to sense engine torque and to anticipate a shift. This causes the clutches to endure an excessive amount of slip, causing heat during the shift and eventually glazes the shifting clutch packs. The other problem with these mechanical kits is the valves supply full line pressure to the delivery rings in the transmission at all times. This constant high pressure causes excessive wear in the transmission. We have spent a great amount of time in the engineering and development of this kit to ensure long transmission life, along with great performance. If the Co-PilotTM kit is installed into a transmission that has been pushed into the fail-safe protection mode (neutral) the effect the Co-PilotTM will have on the transmission is not as apparent as when installed on a stock transmission that has not been previously damaged. After the C-3 (3rd-5th) clutch pack has been glazed a few times the clutch pack looses about 20% of its holding force, in this case the complete ATS Heavy Duty Transmission package may be necessary to repair the previously damaged components inside the transmission.
No Shipping To CA
The Co-Pilot package alone, without any internal transmission modifications, allows the transmission to handle approximately 85 more horsepower and 120 foot pounds of torque over the power level at which the stock Allison will typically enter into "Fail Safe" mode, roughly 425HP/650Tq. The Co-Pilot kit allows the transmissions clutch packs to receive full line pressure (clamping force needed to apply clutches) during high power situations. The stock Allison LCT-1000/2000 and 2400 transmissions torque capacity has been reduced by the limited pressure that is available i the clutch packs. The stock Allison transmission only receives approximately 86-PSI oil pressure to the clutch packs when in 5th gear. After the addition of the Co-Pilot transmission system the transmission clutch packs receive approximately 230-PSI, more than 2.5 times the stock pressure.
FEATURES & BENEFITS:
- Increases clutch pack apply pressure relative to boost, throttle position, and vehicle speed sensor
- More effective than any "shift kit" - Pressure increases more than double what shift kits will do without harsh or erratic shifting!
- Creates a more efficient power transfer by controlling torque converter lockup, which results in cooler transmission running temperatures
- In-cab push button control (adjustable on-the-fly)
- User selectable "Race Mode" which forces lockup after the 1-2 shift while maintaining full line pressure
- Automatically controls an exhaust brake
The biggest factor that causes transmission failures, as noted before, is the fact that apply pressures are too low. They work great for a stock transmission, however, as soon as more power is added, damage is likely to occur. The Trans go shift kit has been used for years with great success, but how successful is it really? The trans go will raise your apply pressure to about 15-PSI or so over stock. This equates to somewhere around 100-PSI. This is a miniscule amount when compared to the ATS Co-Pilot. The common misconception is that it will cause far too much pressure if the Co-Pilot and Trans go are used in tandem. This is false. The only modification is that when drilling the separator plate, it is ideal to only drill out about 65/1000 instead of 100/1000. With these two enhancements used together, a stock Allison will see probably see a 1:1 ratio of line pressure to apply pressure. This will yield incredible results in a stock transmission.
It is often said that timing is everything, and that adage holds true in this scenario. The stock transmission has a very gradual pressure ramp up time, which is another cause of slipping under higher power levels. The Trans go follows the same pressure ramp up time, because it is mechanical, it is simply imitating with magnification of the stock attributes. The Co-Pilot however is electronic and programmed by ATS. We enabled it to bring the pressure up in a fraction of the time, allowing for a greater amount of shock force and clutch grip.
By allowing the available line pressure to the clutch packs, we have designed a system that increases the torque capacity of the stock Allison transmission by over 280 foot pounds of torque with the simple addition of our Co-pilotTM transmission kit. This increased pressure is only applied during high engine torque output, unlike other mechanical kits that do not use electronic controls. This removes the concern of excessive pressure on vital transmission parts such as delivery rings, drums, shafts, etc. during normal operation. Other valve body kits being sold today perform this hydraulically, only after the trim valve has completed the shift. The problems with these hydraulic kits lie in two areas. The first is the lack of ability to sense engine torque and to anticipate a shift. This causes the clutches to endure an excessive amount of slip, causing heat during the shift and eventually glazes the shifting clutch packs. The other problem with these mechanical kits is the valves supply full line pressure to the delivery rings in the transmission at all times. This constant high pressure causes excessive wear in the transmission. We have spent a great amount of time in the engineering and development of this kit to ensure long transmission life, along with great performance. If the Co-PilotTM kit is installed into a transmission that has been pushed into the fail-safe protection mode (neutral) the effect the Co-PilotTM will have on the transmission is not as apparent as when installed on a stock transmission that has not been previously damaged. After the C-3 (3rd-5th) clutch pack has been glazed a few times the clutch pack looses about 20% of its holding force, in this case the complete ATS Heavy Duty Transmission package may be necessary to repair the previously damaged components inside the transmission.
No Shipping To CA
Specifications
- SkuATS-6019244326
- ManufacturerATS Diesel Performance
- MPN601-924-4326
NO VIDEOS AVAILABLE
Blog Posts
Recommended Products
Recently Viewed
Loyalty Rewards
- For each dollar that you spend with us, we reward you with points and we have created three tiers for how many points you'll receive per dollar spent based upon which tier you're in.
-
Diesel Insider ($0-599 spent in the last year):
1 point per $1.00 spent -
Diesel Elite ($600-1199 spent in the last year):
1.2 points per $1.00 spent -
Diesel Expert ($1,200+ spent in the last year):
1.5 points per $1.00 spent - You must create an account or be logged-in to receive loyalty funds
Added To Cart
ATS CoPilot Transmission Controller 07.5-10 GM Duramax
Quantity: 0
Cart Total$0000.00