{"title":"Chips - Programmers - Tuners | 2020-2026 GM 6.6 Duramax L5P","description":"\u003cp\u003eThe 2020 Duramax L5P is rated at 445 horsepower and 910 foot pounds of torque. Due in large part to the new 10 speed Allison transmission, the maximum tow rating increased substantially compared to the previous generation L5P's, but without any actual increase to the engine's output. \u003c\/p\u003e\n\u003cp\u003eFortunately, there are numerous methods for extracting a little, or a lot, of additional horsepower and torque out of the L5P, and some quite honestly are simpler than others, and hands down, the quickest method to add reliable power is with the addition of an aftermarket performance programmer. There are numerous options on the market for tuners, some that are a simple \"hand held\" programmer that plugs into the OBDII under the dash, and then is removed once the programming is complete. Others still plug into the OBDII, but remain installed to act as an interface to allow for various functions, such as gauge display. And finally, others install into the engine bay in-line with various sensors to alter their signal for a power boost.\u003c\/p\u003e\n\u003cp\u003eWe offer programmers from the best in the business, to include, but not limited to Edge, Banks Power, ATS Diesel, BD-Power, and more. If you’re having trouble determining the best route for your performance upgrade, feel free to give us a call and we’d be happy to steer you in the right direction.\u003c\/p\u003e","products":[{"product_id":"afe-77-44010-scorcher-hd-module-gm-l5p","title":"AFE Scorcher HD Module 17-23 GM 6.6L Duramax L5P","description":"How about an extra 60 horsepower and 120 foot pounds of torque out of your L5P with a simple plug and play installation?  That's what you'll get out of the SCORCHER HD Module!\u003cbr\u003e\u003cbr\u003e\nA simple 30 minute install will give you a huge increase in power. The aFe POWER SCORCHER HD Module includes a high quality case  wire harness with factory style connectors for an easy plug  play installation. A LED light switch provides In-Cabin On-The-Fly power adjustments. The 4-Power settings are adjustable with one button and the LED light represent the settings: Stock (Green), Sport (Yellow), Sport+ (Orange) and Race (Red) . This performance module increase turbo boost and fuel pressure. It improves vehicle performance and and \"Low End\" torque. In testing, this module resulted in significant +60 horsepower and up to +120 lbs. x ft. of torque verified by our in house dyno.\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eDIRECT PLUG AND PLAY POWER:\u003cbr\u003e\n\u003c\/b\u003eThis quick and easy plug  play SCORCHER HD module adds significant power by altering pressure sensor signals to increase turbo boost and fuel pressure to improve vehicle efficiency, power and throttle response.\u003cbr\u003e\n\u003cb\u003e\u003cbr\u003e\n\u003c\/b\u003e\u003cb\u003eON-THE-FLY POWER ADJUSTMENTS:\u003cbr\u003e\n\n\u003c\/b\u003eSCORCHER HD modules features In-Cabin On-the-Fly power adjustment to accommodate any situation. This adjustment is controlled by via LED light switch with a button that can be easily mounted in any location in the cabin.\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eHIGH QUALITY CASE AND WIRING:\u003cbr\u003e\n\u003c\/b\u003eaFe SCORCHER HD modules uses high quality aluminum extrusion black powder-coated enclosure casing and factory style connectors which requires no modification to your factory harness. These factory style connectors, plugs directly into the stock wiring harness connectors and sensors.\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eHIGH PRECISION AND QUALITY:\u003cbr\u003e\n\u003c\/b\u003eSCORCHER HD modules are 100% tested for proper protection. These modules work amazingly on stock vehicles and are optimized for maximum performance with use of aFe POWER performance products.\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003e\u003c\/b\u003e","brand":"AFE","offers":[{"title":"Default Title","offer_id":52076809945453,"sku":"AFE-77-44010","price":462.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/16307.jpg?v=1752689195"},{"product_id":"afe-77-84010-scorcher-bluetooth-module","title":"AFE Scorcher Blue Bluetooth Power Module 17-23 GM 6.6L Duramax L5P","description":"\u003cp\u003eEasily add 60 horsepower to your L5P Duramax with this simple plug and play performance module from aFe that you can control from your phone using a Smartphone App or the simple to use in-cab switch, your choice.\u003c\/p\u003e\n\u003cp\u003eThe aFe POWER SCORCHER BLUE Power module is the next generation of plug and play electronic module technology. It is the fastest way to safely gain significant horsepower, torque and improve drivability without modifying or leaving any trace on the Engine Control Unit (ECU). The SCORCHER BLUE features an LED control switch for in-cabin, on-the-fly power adjustments with different preset modes. With Bluetooth connectivity you can tap into your iOS or android device to make power adjustments, custom tune different power modes, view gauges for engine parameters, upgrade to the latest revision, measure acceleration times and more. The app is downloadable for free on the APP Store or Google Play store.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eINCREASE POWER AND PERFORMANCE\u003c\/b\u003e - The SCORCHER BLUE Power module increases fuel pressure and turbo boost and overall vehicle performance producing double-digit power gains on our in-house dyno.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDIRECT PLUG AND PLAY POWER\u003c\/b\u003e - Designed with factory style connectors, it easily connects to engine sensors for a quick and simple install. The LED control switch can be routed through the firewall into the cabin or connect to the module via Bluetooth with the smartphone app.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eON-THE-FLY POWER ADJUSTMENTS\u003c\/b\u003e - In-Cabin, on-the-fly power adjustments can be made to accommodate your driving needs. Select one of four power settings on the in-cab LED control switch or control the module remotely via the free iOS or android app. The smartphone connects to the module via Bluetooth and displays engine parameters (Fuel Pressure and MAP).\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003e4 POWER SETTINGS\u003c\/b\u003e - This Power module have 4-power settings loaded and identifiable with the LED light on the switch or smartphone app. Stock (Green), Sport (Yellow), Sport+ (Orange) and Race (Red).\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eBLUETOOTH CONNECTIVITY\u003c\/b\u003e - The SCORCHER BLUE module is Bluetooth 4.0 capable and can connect to most iOS or android device. The Bluetooth connectivity allows the control of the module while being in the vehicle cabin without running any wire through the firewall.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eSCORCHER BLUE APP\u003c\/b\u003e - The aFe POWER SCORCHER BLUE app is free on the APP Store and Google Play store and allows the smartphone device to become a handheld remote for the module. It also displays fuel pressure and turbo boost gauges, allows you to customize each power mode, upgrade to the latest revision and even measure 0 to 60 and ¼ mile times.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eIMPORTANT NOTE\u003c\/b\u003e - aFe POWER does not recommend using the SCORCHER BLUE module with any other tuners or modules. aFe POWER recommends that only Sport or Sport + settings are used during towing.\u003c\/p\u003e","brand":"AFE","offers":[{"title":"Default Title","offer_id":52076810076525,"sku":"AFE-77-84010","price":581.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/17607.jpg?v=1752689196"},{"product_id":"autometer-signal-splitter-adapter","title":"Auto Meter 5323 OBD-II Signal Splitter Adapter","description":"\u003cp\u003eGauges, programmers, and numerous other upgrades for your truck require a constant stream of data coming through your OBD-II connector under the dash.  In many cases, you can have two devices that you'd like to be plugged in at once, or what if you want to scan the truck for codes or other diagnostics?  You are required to unplug your device in order to gain access to the OBD-II.  With this splitter from AutoMeter, you can have two access points under your dash to aid in simplifying this mess.\u003c\/p\u003e\n\u003cp\u003eThis low profile OBD-II signal splitter \/ pass through alows for remote location of connections for AutoMeter products like AirDrive, DashLink, DashControl and SmartConnect instrumentation while providing an additional easy to access connection point for other onboard devices requiring access to the OBD-II data stream.  This splitter may work with other non-AutoMeter products, as well, but have not been verified by AutoMeter.\u003c\/p\u003e","brand":"Auto Meter","offers":[{"title":"Default Title","offer_id":52076866208109,"sku":"AM-5323","price":42.44,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/17260.jpg?v=1752689397"},{"product_id":"p-16060-bully-dog-30490-bdx-windshield-mount-aspx","title":"Bully Dog 30490 BDX Windshield Mount","description":"\u003cp\u003eBully Dog's BDX Windshield Mount is not your average device mount. The mount's heavy duty suction cup base securely adheres to windshield glass while four ultra-strong neodymium magnets ensure your Bully Dog BDX device stays front-and-center, no matter what terrain you're on.\u003c\/p\u003e","brand":"Bully Dog","offers":[{"title":"Default Title","offer_id":52076926927213,"sku":"BUL-30490","price":25.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/16060.jpg?v=1752689587"},{"product_id":"bullydog-pod-mount-adapter-gt-watchdog","title":"Bully Dog Pod Mount Adapter for GT \u0026 Watchdog","description":"\u003cp\u003eThis simple adapter will make the Watch Dog or GT fit any 2 1\/16\" gauge pod. The Pod Mount Adapter below will accommodate the installation of a gas or diesel GT or a Watch Dog into any 2-1\/16\" standard gauge pod hole. While Bully Dog offers a custom pod mount for many vehicle applications, gaps do exist between our electronic products and Custom Gauge Pods. The Pod Mount Adapter is perfect for use with another manufacturer's custom gauge pod, in case Bully Dog does not support a particular vehicle application with a custom gauge pod mount.\u003c\/p\u003e","brand":"Bully Dog","offers":[{"title":"Default Title","offer_id":52076927287661,"sku":"BUL-30420","price":14.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/7084.jpg?v=1752689589"},{"product_id":"bully-dog-sensor-docking-station","title":"Bully Dog Sensor Docking Station With Pyrometer BUL-40384","description":"The Bully Dog Sensor Docking Stations offers an unparalleled glimpse into the health of your vehicle. This accessory for the GT and the watchdog product lines makes it easy to install aftermarket automotive sensors onto your vehicle and display those sensor values on your GT or Watchdog. The docking station supports a multitude of different sensor types including exhaust temperature, pressure sensors, oil pressure or boost, speed sensors, and temperature sensors. This Docking Station comes with one Pyrometer.","brand":"Bully Dog","offers":[{"title":"Default Title","offer_id":52076927418733,"sku":"BUL-40384","price":169.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/8209.jpg?v=1752689589"},{"product_id":"daystar-donotflash-obd-plug-ku71124bk","title":"Daystar Do Not Flash OBD Plug KU71124BK","description":"\u003cp\u003eIf you've ever had the dealer flash over a performance tune stored in your ECM, you know how difficult it can be to get a recovery file from the manufacturer to restore your programmer.  In order to avoid this problem when going to the dealer, plugging this simple blocker plug into your OBDII port can save you a lot of headache.\u003c\/p\u003e","brand":"Daystar","offers":[{"title":"Default Title","offer_id":52076943802733,"sku":"DAY-KU71124BK","price":16.54,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/8786.jpg?v=1752689648"},{"product_id":"diablosport-9050-trinity-2-monitor","title":"DiabloSport 9050 Trinity 2 (T2 MX) Monitor Only","description":"Are you ready for the most intuitive, easy to read monitor and data logging interface on the market?  Let us introduce you to the Trinity 2.\u003cbr\u003e\u003cbr\u003eFeaturing a high resolution, 5\" capacitive touch screen, full swipe functionality, industry-leading gauge designs, unmatched customization potential, and a powerful, yet simple, user interface. The T2 MX is unlike anything else on the market.  Add the MX for a sharp, clean monitor to offer you in-depth data in real-time to always know what is happening under the hood.  Having trouble with a pesky check engine light or trouble code?  Use the T2 MX to read and clear codes and save yourself an unnecessary trip to your local dealer or service center.  \u003cbr\u003e\n\u003cbr\u003e\nThe T2 MX is the perfect addition for any 1996 or newer vehicle.  Analog gauges are a thing of the past as the Trinity 2 gives you expanded monitoring capabilities, diagnostics, performance tests, data logging, and a path to upgrade to a full-featured performance tuner with an easy internet update.  Configuration and custom layout options are plentiful with the MX.  Set up the gauge layout to provide you with the most meaningful data for your vehicle and change at any time!  With high-definition graphics, an industry-leading display, and legendary DiabloSport quality, the T2 is the best upgrade you can add to your ride. \u003cbr\u003e\n\u003cbr\u003e\n\n\u003cb\u003eUPGRADE OPTIONS:\u003cbr\u003e\n\u003c\/b\u003eThe Trinity 2 MX is the most advanced gauge display on the market, however, some may want to add power, mileage potential, and improved drivability.  With the T2 MX, you are not stuck with just the best gauge display as it can be upgraded into a full-featured, tire roasting, Trinity T2 EX performance tuner.","brand":"DiabloSport","offers":[{"title":"Default Title","offer_id":52076944753005,"sku":"DS-9050","price":685.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/17192.jpg?v=1752689652"},{"product_id":"diablosport-trinity-pigtail-cable","title":"DiabloSport Trinity T1000 Analog Pigtail Cable","description":"\u003cp\u003eThe T1015 allows Trinity Users to plug in and monitor or record their favorite aftermarket analog sensor device. The T1015 will allow you to hook up sensors like Innovate Motorsports wide band controllers, PLX Devices, EGT sensors and much more! This is a two channel connector that has two bare signal leads and two ground wires.\u003c\/p\u003e","brand":"DiabloSport","offers":[{"title":"Default Title","offer_id":52076944916845,"sku":"DS-T1015","price":26.11,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/10985.jpg?v=1752689653"},{"product_id":"p-4989-edge-98202-back-up-camera-for-cts-monitors-aspx","title":"Edge 98202 Back-Up Camera for CTS\/CTS2 Monitors","description":"The CTS\/CTS2 line of products have a built-in video port that allows users to connect Edge's new state-of-the-art back-up camera. The CTS's high-resolution, 4.3 inch color screen allows users to see what's going on behind them with the Edge camera connected. The camera mode on the CTS automatically engages when the vehicle goes into reverse*. The back-up camera option is a must have for towers and safety-conscious drivers.\u003cbr\u003e\u003cbr\u003e\n\u003cb\u003eIMPORTANT NOTES:\u003c\/b\u003e\n\u003cul\u003e\n    \u003cli\u003eCamera automatically engages on supported vehicles with automatic\n    transmission where we can read the gear parameter.  Not available on all\n    models.\u003c\/li\u003e\n    \u003cli\u003eCTS monitor not included with purchase of camera.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52076970508653,"sku":"EDG-98202","price":330.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/4989.jpg?v=1752689744"},{"product_id":"edge-98602-eas-starter-kit-cable","title":"Edge EAS (Edge Accessory System) Starter Kit Cable","description":"\u003cp\u003eThe Edge Accessory System (EAS) was created with future expandability in mind. The EAS allows users to connect multiple accessories inline to an existing EDGE monitor. The ability to daisy-chain multiple accessories using the EAS allows users to monitor and display dozens of parameters and usefully info all in one place using a single EDGE device. \u003cbr\u003e\u003cbr\u003eEAS Starter Kits work with the CS, CTS, TrailDash and Dashpaq EDGE monitors. Keep in mind this is the starter kit only. It simply allows the additions of EAS accessories such as an EAS EGT probe, EAS Juice adapter, and many more. Each EAS add-on is sold separately.\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52076970672493,"sku":"EDG-98602","price":74.89,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/8d471ac496d01480ea951be8673204b00f20e903.webp?v=1760550397"},{"product_id":"edge-98611-eas-egt-expandable-kit","title":"Edge 98611 EAS EGT Expandable without Starter Kit","description":"The EGT probe is a sensor that allows users to monitor critical Exhaust Gas Temperatures to ensure added power is not creating excessive heat which, in turn, can cause engine damage. With the EAS system a user can connect multiple EGT sensors to monitor temperatures in different locations and compare readings to be even more precise. \u003cbr\u003e\u003cbr\u003eThe Edge Accessory System (EAS) was created with future expandability in mind. The architecture of the EAS allows users to connect multiple accessories, daisy-chain style, to the CS and CTS platform. The ability to daisy-chain multiple accessories using the EAS allows users to monitor and display dozens of parameters on a single device. \u003cbr\u003e\u003cbr\u003eEAS Starter Kits are only available to work with the CS and CTS product lines. In order to use the EAS accessories you must have an EAS Starter kit (part # 98602). EAS Starter kits come standard with all Juice with Attitude CS and CTS products and the EAS Starter Kit with Expandable EGT (part # 98603).\u003cbr\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52076970836333,"sku":"EDG-98611","price":181.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/15748.jpg?v=1752689745"},{"product_id":"edge-98609-eas-switch-with-starter-kit","title":"Edge 98609 EAS Power Switch with Starter Kit","description":"\u003cp\u003eTired of your dash being cluttered with switches for lights, compressors, etc.?  Edge CTS owners now have an option for a completely integrated dash, all ran through your Edge CTS Insight, Evolution, or Juice with Attitude!\u003c\/p\u003e\n\u003cp\u003eThe Edge EAS (Expandable Accessory System) Power Switch allows CTS owners to install the new switch system and use Edge's MyStyle software to name your accessory to display right on the screen and take advantage of Edge's clean EAS daisy chain system to turn engage and disengage your truck's accessories.\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52076970869101,"sku":"EDG-98609","price":215.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/10994.jpg?v=1752689745"},{"product_id":"p-15752-edge-98616-eas-control-kit-aspx","title":"Edge 98616 EAS Control Kit","description":"Tired of your dash being cluttered with switches for lights, compressors, etc. plus want a way to accurately monitor EGT (Exhaust Gas  Temperature)?  Edge CTS and CTS2 owners now have an option for a completely integrated dash, all ran through your Edge CTS Insight, Evolution, or Juice with Attitude plus EGT monitoring capabilities.\u003cbr\u003e\u003cbr\u003eThe EAS Control Kit gives you the ability to monitor EGTs and adds the power switch to control multiple accessories with an On\/Off digital power switch right on your CTS or CTS2 monitor. \u003cbr\u003e\n\u003cbr\u003e\nThe EGT probe is a sensor that allows users to monitor critical Exhaust Gas Temperatures to ensure added power is not creating excessive heat which, in turn, can cause engine damage. This kit is ideal for the daily diesel driver or if you are towing, then it's a must have! Towing can put a lot of strain on the truck and make it run hot. Don't be left on the side of the road with an overheated truck because you didn't watch your Exhaust Gas Temperatures with the Edge EAS EGT. \u003cbr\u003e\n\u003cbr\u003e\nThe EAS Power Switch is a tremendous feature for truck owners! Customers can now hook up accessories like aftermarket lights, air compressors, etc. and engage them from the CTS\/CTS2 device. Install the new switch and either use Edge's MyStyle software to name your accessory or with the CTS2 rename those accessories right from your device. The CTS2 comes with a screen layout that can monitor up to 6 gauges and 4 rocker switches for the ultimate control. Take advantage of Edge's clean EAS daisy chain link system to turn your truck's tools on\/off. \u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eKIT CONTENTS: \u003c\/b\u003e\u003cbr\u003e\n\u003cul\u003e\n    \u003cli\u003eEAS Starter Kit \u003c\/li\u003e\n    \u003cli\u003eEAS EGT Probe \u003c\/li\u003e\n    \u003cli\u003eEAS Power Switch\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52076970967405,"sku":"EDG-98616","price":423.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/15752.jpg?v=1752689745"},{"product_id":"edge-98617-eas-competition-kit","title":"Edge 98617 EAS Competition Kit","description":"The Edge EAS Competition Kit is the ideal solution for those that either do not have an OBDII port (such as a 12 valve Cummins) and want to run an Edge Insight or possibly you don't trust the factory sensors or they simply don't operate in the range you have built your truck for.  The Competition Kit provides you with the necessary sensors that will allow you to read EGT (Exhaust Gas Temperature), one 0-100 pressure (such as boost), and a -40 to 300 degree temperature (such as transmission temperature) the  way via physical sensors being installed, but through the cutting edge Insight device.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eKIT CONTENTS:\u003c\/b\u003e\n\u003cul\u003e\n    \u003cli\u003eEAS Starter Kit \u003c\/li\u003e\n    \u003cli\u003eEAS EGT Probe \u003c\/li\u003e\n    \u003cli\u003eEAS Universal 5 Volt \u003c\/li\u003e\n    \u003cli\u003eEAS 0-100 PSIg Pressure Sensor \u003c\/li\u003e\n    \u003cli\u003eEAS -40F to 300F Temperature Sensor\u003c\/li\u003e\n\u003c\/ul\u003e\nThe EAS Competition Kit gives users the ability to monitor EGTs and add an additional 0-100 PSIg boost and -40F to 300F temp sensors for ultimate control. This kit is designed for those truck owners who have upgraded turbo or turbo's and other mods ,where the stock sensors just aren't enough anymore. \u003cbr\u003e\n\u003cbr\u003e\nThe EAS EGT probe is a sensor that allows users to monitor critical Exhaust Gas Temperatures to ensure added power is not creating excessive heat which, in turn, can cause engine damage. This kit is ideal for the daily diesel driver or if you are towing then it's a must have! Towing can put a lot of strain on the truck and make it run hot. Don't be left on the side of the road with an overheated truck because you didn't watch your Exhaust Gas Temperatures with the Edge EAS EGT. \u003cbr\u003e\n\u003cbr\u003e\nThe EAS 0-100 PSIg Boost Sensor is the perfect sensor for an aftermarket turbo that can build more boost than the stock MAP sensor can read. Simply install this sensor, use MyStyle to set up the sensor, and have the ability to see what kind of boost you can build. Or maybe you are trying to fine tune your truck and need to install a drive pressure sensor or fuel pressure sensor the Edge 0-100 PSIg sensor is your answer. \u003cbr\u003e\n\u003cbr\u003e\nThe EAS Temperature Sensor is a -40F to 300F 1\/8 NPT sensor that will allow you to monitor things like Transmission Temp., Differential\/Axle Oil Temp., Oil Temp., Engine Coolant Temp., Air Intake Temp., Pre and Post Intercooler Temp., and many more. Another great solution for those with aftermarket accessories. \u003cbr\u003e\n\u003cbr\u003e\nAdditionally, Edge's Data Logging Software allows you to export all data logs into a CSV (Excel) file to save and compare runs, view, graph and improve tuning. To view CSV data log files, you must use MyStyle software or export it from MyStyle software. These options make the Insight CS2 and CTS2 the industry leader in digital gauge\/data logging for any enthusiast!","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52076971065709,"sku":"EDG-98617","price":562.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/15746.jpg?v=1752689745"},{"product_id":"edge-98618-eas-data-logging-kit","title":"Edge 98618 EAS Data Logging Kit","description":"The Edge EAS Data Logging Kit is tailored for those that love data, and lots of it.  This kit when paired with an Edge CS, CS2, CTS, or CTS2 monitor allows you to monitor a plethora of powertrain vitals, store them, and even export data logs into an Excel file.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eKIT CONTENTS:\u003c\/b\u003e\n\u003cul\u003e\n    \u003cli\u003eEAS Starter Kit \u003c\/li\u003e\n    \u003cli\u003eTwo EAS EGT Probe \u003c\/li\u003e\n    \u003cli\u003eTwo EAS Universal 5 Volt \u003c\/li\u003e\n    \u003cli\u003eTwo EAS 0-100 PSIg Pressure Sensor \u003c\/li\u003e\n    \u003cli\u003eTwo EAS -40F to 300F Temperature Sensor\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cbr\u003e\nThe EAS Data Logging Kit is for the ultimate diesel enthusiast! This kits gives users the ability to monitor EGTs in two different locations, two 0-100 PSIg boost sensors, and two -40F to 300F temp sensors for unmatched monitoring. This kit is designed for truck owners who have upgraded turbo or turbo's, and other mods where the stock sensors just aren't enough anymore. Truck owners who use trucks for dyno competitions, sled pulls, and drag racing need this kit. Fine tuning these trucks can be difficult, but with the Edge Data Logging Kit you can log runs, view logs, and make adjustments as needed for maximum performance. \u003cbr\u003e\n\u003cbr\u003e\nThe EAS EGT probe is a sensor that allows users to monitor critical Exhaust Gas Temperatures to ensure added power is not creating excessive heat which, in turn, can cause engine damage. This kit is ideal for the daily diesel driver or if you are towing then it's a must have! Towing can put a lot of strain on the truck and make it run hot. Don't be left on the side of the road with an overheated truck because you didn't watch your Exhaust Gas Temperatures with the Edge EAS EGT. \u003cbr\u003e\n\u003cbr\u003e\nThe EAS 0-100 PSIg Boost Sensor is the perfect sensor for an aftermarket turbo that can build more boost than the stock MAP sensor can read. Simply install this sensor, use MyStyle to set up the sensor, and have the ability to see what kind of boost you can build. Or maybe you are trying to fine tune your truck and need to install a drive pressure sensor or fuel pressure sensor the Edge 0-100 PSIg sensor is your answer. \u003cbr\u003e\n\u003cbr\u003e\nThe EAS Temperature Sensor is a -40F to 300F 1\/8 NPT sensor that will allow you to monitor things like Transmission Temp., Differential\/Axle Oil Temp., Oil Temp., Engine Coolant Temp., Air Intake Temp., Pre and Post Intercooler Temp., and many more. Another great solution for those with aftermarket accessories. \u003cbr\u003e\n\u003cbr\u003e\nAdditionally, Edge's Data Logging Software has the ability to export all data logs into a CSV (Excel) file to save and compare runs, view, graph and improve tuning. To view CSV data log files, you must use MyStyle software or export it from MyStyle software. These features make the Insight CS2 and CTS2 the industry leader in digital gauge\/data logging for any enthusiast!","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52076971098477,"sku":"EDG-98618","price":1229.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/EDG-98618.jpg?v=1752689746"},{"product_id":"p-4990-edge-98620-eas-expandable-egt-probe-kit-with-lead-aspx","title":"Edge EGT Probe \u0026 EAS (Edge Accessory System) Starter Kit Cable Kit","description":"\u003cp\u003eIf you're running one of Edge's CS, CTS, CS2, CTS2, CTS3, TrailDash or Dashpaq Monitors you have the ability to monitor a plethora of different engine and powertrain vitals. However, you could be missing out on one of the most important thing to watch, your exhaust gas temperate (EGT).\u003c\/p\u003e\n\u003cp\u003eThis probe is designed to work in conjunction with Edge's exclusive EAS (Expandable Accessory System) to allow you to daisy chain multiple sensors. Otherwise, this sensor works perfectly as a stand alone with your existing monitor. Built with a 15\" lead, if the need ever arises, you can easily replace only the probe without replacing the entire harness down the road.\u003c\/p\u003e\n\u003cp\u003eThe EGT temperature probe must be installed in the exhaust manifold for the most accurate temperature readings. The closer to the combustion chamber, the better. Most trucks will require drilling and tapping of the exhaust manifold to 1\/8-NPT (bit and tap not included). This kit includes exhaust manifold fitting, probe, wiring, and an expandable EAS starter cable. So adding more accessories down the road is plug-n-play.\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52076971229549,"sku":"EDG-98620","price":191.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/4990.jpg?v=1752689746"},{"product_id":"edge-98004-gauge-pillar-adapter","title":"Edge Products 98004 Universal Gauge Pillar Adapter for CS CS2 CTS CTS2 CTS3","description":"If you've ever wanted a clean, factory looking installation for your Edge Insight, Evolution, or Juice with Attitude CS, CS2, CTS, CTS2, and CTS3 Edge has their universal adapter to get the job done.  This adapter allows you to mount any of their CS or CTS units in any 2 1\/16\" gauge pod, such as an Autometer.  The adapter's state of the art swivel system gives you the flexibility to adjust the monitor to your own optimal viewing angle.","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52076973130093,"sku":"EDG-98004","price":46.05,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/8608.jpg?v=1752689754"},{"product_id":"edge-products-98005-cts2-pod-adapter","title":"Edge Products 98005 CTS2 Pod Adapter Kit","description":"This adapter is required when installing an Edge CTS2 (Color Touch Screen) into one of Edge's custom dash mounts.\u003cbr\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52076973162861,"sku":"EDG-98005","price":29.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/15751.jpg?v=1752689754"},{"product_id":"ezlynk-auto-agent-3-tuning-device","title":"EZ LYNK Auto Agent 3 Cloud Based Diagnostics Device","description":"\u003cp\u003eThe Auto Agent 3 from EZ LYNK is the most advanced vehicle diagnostics device to hit the automotive market. This device plugs into your vehicle's OBDII port under the dash and communicates with your smartphone using the free Auto Agent App.\u003cbr\u003e\u003cbr\u003eHave you ever found yourself frustrated when there's been an issue with your vehicle, and you take it to the mechanic, and the issue has magically resolved itself, only to return at a later time? Or you take it to the dealer, they diagnose the issue, and must order the parts that can take weeks to arrive? What if your mechanic could remotely \"tap into\" your vehicle's computer while you're having issues to avoid repeated trips to the shop to have it resolved, saving time AND money? Further, what if that issue could be resolved by a simple ECM update, and the mechanic can do that remotely, as well, eliminating the need to even go to the shop? \u003cb\u003e Yes, this is a reality with the EZ LYNK!\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eEZ LYNK AUTO AGENT 3 DETAILS:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AutoAgent 3 connects to the vehicle via the OBDII port and broadcasts a Wi-Fi access point (AP), which allows a wireless connection to the vehicle using any iOS or Android device. By launching the free EZ LYNK application, engine data is seamlessly streamed to the phone or other smart devices. The AutoAgent can also re-flash vehicle system controllers with ECU profiles shared by technicians.\u003c\/p\u003e\n\u003cp\u003eTechnicians will quickly learn to appreciate the EZ LYNK Cloud, where they can easily manage customers\/vehicles and all the data associated with them (datalogs, engine profiles, vehicle information).\u003cb\u003e Transferring engine profiles via USB connection, SD card, or e-mail is now a thing of the past\u003c\/b\u003e as technicians have the capability to share engine profiles with the click of a button to eliminate user error from the equation.\u003c\/p\u003e\n\u003cp\u003eOn the other side of things, the end-user can conveniently share datalogs and other vehicle information to any technician with the touch of a finger without even leaving the driver's seat. Datalogs can be quickly started and stopped from the main gauge display screen and bookmarks can be added to draw interest to the specific points of a datalog if desired.\u003c\/p\u003e\n\u003cp\u003eA fully customizable user interface allows the end-user to create a gauge interface that suits their particular needs. Technicians can also create default PID configurations that are automatically loaded during a reflash procedure to further assist in the troubleshooting and diagnostic process.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSCAN TOOL:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe Auto Agent app provides insight into critical vehicle sensor data, allowing you to monitor in real time the health and status of your vehicle. Using the integrated, adjustable alarms, you’ll be alerted if parameters get out of range. \u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eLIVE DATA:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eView and Record vehicle data in real time with the Auto Agent App. Customize units and format layout in Digital Tiles, Analog Gauges, or view data over time as a Line Graph, all to your liking. Share recorded data Over-The-Air with any technician of your choice in seconds.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVEHICLE FUNCTIONS:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eKeep your vehicle in good health while saving a trip to the Dealership by performing technician-recommended vehicle functions in the Auto Agent App Anywhere, Anytime.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eService your Diesel Vehicle Emissions with Stationary DeSoot\u003c\/li\u003e\n\u003cli\u003ePerform a Transmission Quicklearn\u003c\/li\u003e\n\u003cli\u003eAdjust tire pressure monitoring (TPMS) thresholds to match installed tire ratings\u003c\/li\u003e\n\u003cli\u003eCorrect your speedometer to match resized tires\u003c\/li\u003e\n\u003cli\u003eAdjust Fuel Tank Capacity after changing your tank size\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eREAD AND CLEAR DTC'S\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eDiagnostic Trouble Codes are your car's way of telling you what is wrong with its health. The Auto Agent app allows you to easily understand what your vehicle is trying to tell you and clear the code after the repair is made.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eO-T-A Firmware Updates\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eSimilar to your Smartphone, today's complex vehicles often require periodic firmware updates to their various systems. The Auto Agent® App keeps you up-to-date by instantly notifying you when updates are provided by any technician of your choice, through the EZ LYNK Cloud. Your vehicle can be updated anytime, anywhere in minutes, without making a trip to the repair shop.\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e","brand":"EZ LYNK","offers":[{"title":"Default Title","offer_id":52076974670189,"sku":"EZ-100EE00AA3","price":549.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/F198752287.png?v=1752689759"},{"product_id":"longhorn-fab-shop-switch-mount","title":"Longhorn Fab Shop 201051 DSP5 | CSP5 | Universal Switch Mount","description":"\u003cp\u003eWhether you're running EFILive, EZ LYNK, or have any other use for a switch in your truck, if you're like us, its always sketchy drilling a hole in your dash, especially in a brand new truck.  Sometimes you're unsure if you'll really like the switch in that location, or not exactly sure what lies behind the plastic you're drilling.  Take all of these questions out of the equation with this simple to install mount from Longhorn Fab Shop.\u003c\/p\u003e\n\u003cp\u003eThis switch mount is perfect to mount your DSP5, CSP5 or any other switch that requires a standard 3\/8\" hole.  Comes standard with the clocking holes that keep your switch from spinning once it is mounted!  The top has multiple mounting locations and angles to make it fit your needs perfectly.\u003c\/p\u003e","brand":"Longhorn Fab Shop","offers":[{"title":"Default Title","offer_id":52077054558573,"sku":"LFS-201051","price":31.63,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/17291.png?v=1752690021"},{"product_id":"mob-armor-magnetic-cell-phone-holder","title":"Mob Armor Large Mob Mount Switch Magnetic Cell Phone Holder","description":"\u003cp\u003eYou've got a cool truck, a cool phone, you deserve a cool phone mount that's also as tough as your truck.  Introducing the Mob Mount featuring robust construction and a super strong magnet to make retrieving your phone holder simple, but still able to handle relentless abuse.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eYour Phone, Your Case\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eThere are so many different cases on the market that Mob Armor didn't want to restrict what case you use based on their phone mounts. So they developed a unique slide system that allows you to use almost any phone and case that you have with our mount.\u003c\/p\u003e\n\u003cp\u003eThis mount is built to hold your device through some of the most extreme off-road racing conditions on earth. We are pretty confident that it will be able to handle just about anything that you can put it through. Built for Off Road, by Off-Roaders.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eHardcore Magnets\u003c\/b\u003e - Don't be fooled, these magnets are no joke. They are 90lb pull force neodinium rare earth magnets that are designed for industrial use. These will keep your phone in place even if you roll your vehicle or if you hit a big pothole on the road.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\"Powerful magnet? Wont that damage my phone?\"\u003c\/em\u003e Actually no. While these magnets are incredibly strong, your phone will be perfectly safe. Mob Armor has done extensive testing to make sure that these magnets do not effect the function of your phone.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eLots of Tilt, Lots of Rotation\u003c\/b\u003e - Why have an awesome magnetic phone mount if it cant tilt? Why have a great tilting phone mount if it can't rotate? The Mob Mount Magnetic is made with a ball housing that supports 70 degrees of tilt and 360 degrees of rotation.\u003c\/p\u003e\n","brand":"Mob Armor","offers":[{"title":"Default Title","offer_id":52077097517421,"sku":"MOBM2-BLK-LG","price":59.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/16556.png?v=1752690173"},{"product_id":"p-16559-mob-armor-mobnetic-plates-aspx","title":"Mob Armor Mobnetic Plates","description":"The MobNetic plate is perfect for mounting your device to a MobNetic or Mobnetic Pro. Coming in at a mere 0.020 of an inch thick, these plates are designed to fit on your phone\/case or behind your case and will not change the look or feel of your device.\u003cbr\u003e\u003cbr\u003eThe MobNetic already comes with one Square mounting plate and one round mounting plate.  Now you can add more mounting plates to other devices to use with your MobNetic or MobNetic Pro.  \u003cbr\u003e\n\u003cbr\u003e\nAdding additional MobNetic plates to your phone and case will increase the mounting strength which may be desired for light off-road use. \u003cbr\u003e\n\u003cbr\u003e","brand":"Mob Armor","offers":[{"title":"Default Title","offer_id":52077097353581,"sku":"MOBN-PL-ACC","price":16.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/MOBN-PL-ACC_1__64560.1554241718.png?v=1752690173"},{"product_id":"mob-armor-elite-cell-phone-holder","title":"Mob Armor Mobnetic Maxx Magnetic Cell Phone Holder","description":"\u003cp\u003eYou need a cell phone mount for your truck.  When you hop in, what do you do with your phone, throw it on the dash?  Keep it in your pocket?  Maybe it goes on the center console where it slides all over the place.  If you want an easy to use mount that doesn't take up any room on your dash, you've found it. The Mobnetic Maxx uses super strong magnets that will keep your phone within arm's reach no matter the terrain you're on.\u003c\/p\u003e\n\u003cp\u003eThe dual 90lb pull force magnets provide a mounting solution for multipurpose use in your vehicle, in the shop, and anywhere you go. Instant docking for your smartphone or other devices with effortless pan and 90 degree tilt adjustment.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eHOW IT WORKS:\u003c\/b\u003eThe Mobnetic Elite includes the swivel and two Mobnetic plates, one for your phone and one for the mounting surface.  This will allow you to stick one of their discs onto your dash, or wherever you prefer, that gives something for the Mobnetic to magnetize to.\u003c\/p\u003e","brand":"Mob Armor","offers":[{"title":"Default Title","offer_id":52077097451885,"sku":"MOBN-MX-BLK","price":49.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/MOBN-MX-BLK_2.jpg?v=1752690173"},{"product_id":"mob-armor-mounting-discs-2-pack","title":"Mob Armor Mounting Discs (2 Pack)","description":"You can never have enough mounting discs. Give yourself more options with extra hardware that will allow you to use your Mob Mount in more places securely. (two discs included per quantity)\u003cbr\u003e","brand":"Mob Armor","offers":[{"title":"Default Title","offer_id":52077097615725,"sku":"MOB-MD","price":12.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/16560.jpg?v=1752690174"},{"product_id":"sct-exhaust-gas-temperature-sensor-kit","title":"SCT Exhaust Gas Temperature Sensor Kit","description":"For Use With SCT X4 and Livewire Programmers\u003cbr\u003e\u003cbr\u003eIf you're running an X4 or Livewire, why not have the ability to read your EGT's?  Because the vehicle's ECM does not read this parameter, you must install a separate pyrometer probe to direct this vital information for your SCT unit to display, and this kit makes that possible.\u003cbr\u003e\n\n\u003cbr\u003e","brand":"SCT","offers":[{"title":"Default Title","offer_id":52077152960877,"sku":"SCT-9817","price":185.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/12401.jpg?v=1752690367"},{"product_id":"afe-77-91001-agd-gauge-monitor-55-2008","title":"AFE 77-91001 AGD Advanced 5.5\" Gauge Display Monitor 08-23 Ram\/Ford\/GM Diesel Trucks","description":"\u003cp\u003eAFE's AGD, or Advanced Gauge Display, is the latest in vehicle monitoring technology. This system will allow you to monitor, record, and control your vehicles parameters and diagnostic information on any 2008 and newer diesel truck. The AGD simply plugs into your OBDII port and start accuratly monitoring your truck with over 25 parameters for every vehicle. The 5.5\" touch screen allows you to navigate the customizable screen easily. This device also features Bluetooth connectivity for use with AFE's Scorcher Blue modules as well as third part tunes. The AGD comes with everything needed to start monitoring your truck including a windshield mount with magnetic base.\u003c\/p\u003e\u003cp\u003e\n\u003c\/p\u003e\u003col\u003e\n\u003cli\u003e\n\u003cb\u003eAccurate On-The-Fly Monitoring:\u003c\/b\u003eIn addition to over 25 parameters available for every single vehicle, there are also multiple application specific options to choose from.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eDiagnostic Data Capabilities:\u003c\/b\u003eWith the ability to run specific diagnostic tests as well as read and clear codes, the AGD can spot potential issues and ensure your vehicle is running at the best of its ability. In addition to the parameters of your choice, driving coach and vehicle performance data can be monitored.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eCustomizable High-Definition Display:\u003c\/b\u003eThe AGD's 5.5\" multi-touch screen makes for a simple yet good looking overview of the parameters most improtant to you. With customizable gauges and multiple different screen layouts available, each display can be tailored to your vehicle's specific needs and aesthetic\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eBluetooth 4.0 Compatibility:\u003c\/b\u003eNot only does it work seamlessly in conjunction with AFE Power's Scorcher BLUE modules, but the AGD also provides the ability to control multi-position tunes from third party companies.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eSimply OBDII Plug-in Connection:\u003c\/b\u003eThe AGD simply plugs in to your vehciles OBDII port. All necessary cables for installation are included. Thanks to its magnetic base, the device can be easily removed from the windshield mount without unplugging any wires.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"AFE","offers":[{"title":"Default Title","offer_id":52077271810413,"sku":"AFE-77-91001","price":522.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/7791001.jpg?v=1752690763"},{"product_id":"edge-eas-obdii-pass-through-splitter","title":"Edge 98106 EAS OBDII Pass Through Splitter","description":"\u003cp\u003eThe OBDII Pass-Through Splitter allows two products to be simultaneously plugged into the OBDII port at the same time. The OBDII pass-through gives the ability to connect two products, such as an Edge CTS2 unit, and another product, including, but not limited to, power running boards or custom tuning devices. This new OBDII splitter is fully populated with a 16-pin pass-through, pinned connector.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e\n\u003cp\u003eUsing this new OBDII splitter, along with the new update for the Edge Insight CTS2, users can operate the Insight monitor in one port and other devices on the other port.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077283737965,"sku":"EDG-98106","price":63.19,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/EDG-98106_1.jpg?v=1772468030"},{"product_id":"p-banks-67102-derringer-tuner-with-idash-18-2020-66l-gm-duramax-l5p","title":"Banks Derringer Tuner with iDash SuperGauge 20-22 GM 2500HD\/3500 6.6L Duramax L5P","description":"\u003cp\u003eAdd power and fuel economy to your Duramax with the most trusted name in diesel performance, Banks Power.\u003c\/p\u003e\n\u003cp\u003eStop the competition dead in their tracks with the Derringer Tuner. Banks delivers torque and power gains across the full operating rpm range, starting right off idle and marching to the shift point in each gear. Derringer is dyno calibrated to use multiple data inputs such as throttle position, RPM, vehicle speed, AFR, knock and coolant temperature, just like your engine's ECU. Its microprocessor based electronics are able to actively and safely optimize calibrations in real time. No competitive product does that.\u003c\/p\u003e\n\u003cp\u003eDerringer has six switched settings. Level 6 produces Best in Class performance that knocks you back in your seat. The Level 3 setting is for work use and has great mid-range feel. When running Level 3 with a loaded work truck and\/or pulling a trailer, your on ramp merging speeds and passing times are greatly improved.\u003c\/p\u003e\n\u003cp\u003eThe electronics are molded into a waterproof connector, which is easily concealed and communicates using B-Bus (Banks Bus) with other devices such as the iDash Super Gauge\/Control Center. The Derringer connects in line with the Throttle Inlet Pressure (TIP) and Manifold Absolute Pressure (MAP) sensors. But, unlike others it also connects to the vehicle's OBDII diagnostic bus connector. A CAN (controller area network) transceiver chip communicates with OBD or B-Bus allowing Banks' microprocessors to talk with the vehicle. On top of that, Derringer's special coolant temp watchdog prevents power addition when the engine is too cold or overheated. The Derringer also auto-adjusts power if knock occurs due to bad fuel. Maximum safe power is all automatic with a Derringer, you just choose your setting.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eThe Banks difference when it comes to L5P POWER!\u003c\/b\u003e - Derringer has 6 power levels, adjustable on-the-fly, with a best gain of +117 hp pushing power well above 520 wheel hp to the road. Plus, the massive increase of +225 lb-ft of torque is situated right in the heart of the power band where you need it most. \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eHow the Derringer does what it does, and why.\u003c\/b\u003e - There's no easy way to make more power for your daily driven L5P with GM's ECU and factory turbo, no magic flash or special \"chip\" available. Banks had to go the tuner route, and making an inline tuner for your truck was no easy task. Banks has almost a thousand man-hours into Derringer development. Fortunately, they've been making tuners for 20 years, so it was all in a day's work.\u003c\/p\u003e\n\u003cp\u003eThe Derringer is a plug-and-play microcomputer designed for easy installation, it's waterproof for convenient under hood mounting, and connects to the iDash Data Pro Powertrain Information Center for the ultimate in information and power selection, unlocking three additional power levels.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eAutoRate\u003c\/b\u003e - Unlike the fixed tuning used by others, the Derringer calibration is continuously adjusting to provide you the peak possible performance under every driving condition. By utilizing the power of the OBD-II data, the tuner intelligently fine-tunes its calibration on the fly without you having to change its power level.\u003c\/p\u003e\n\u003cul\u003e\n    \u003cli\u003e\n\u003cb\u003eExhaust Gas Temperature (EGT)\u003c\/b\u003e - The Derringer senses your engine's EGT and intelligently modulates fueling to maintain a safe maximum EGT, protecting your turbo and engine.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eAltitude compensation\u003c\/b\u003e - The Derringer senses ambient air pressure, controlling the turbocharger to maintain added boost and power as altitude increases.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eCoolant Temperature Monitoring\u003c\/b\u003e - The Derringer senses coolant temp to control added power. During warmup, no power is added below 120° F, then power is ramped in and fully available above 150° If the coolant overheats for any reason, the Derringer starts removing its power at 230° F and additional power is totally removed if you exceed 240° F.\u003c\/li\u003e\n    \u003cli\u003e\n\u003cb\u003eFull Power Timer\u003c\/b\u003e - If set on Sport level, the Derringer allows for 30 seconds of wide open throttle before transitioning to the recommended power level for sustained tow\/haul. (Our research has shown that the stock L5P when at full power will hit 1450° EGT and after a minute or so will pull out fuel to cool things down. So, we do the same thing.)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eTransCommand Active Transmission Safety System\u003c\/b\u003e - In addition to AutoRate Adaptive Tuning, the Derringer High Output is calibrated to modulate power during shifts for better clutch engagement. Thanks to its OBD connectivity, Derringer knows when the GM\/Allison 10-speed transmission is shifting gears. It reduces its added power momentarily to allow for a smooth shift. Competitive tuners have no idea or simply ignore when the transmission is shifting and continue to add power, overspeeding the transmission and causing long-term damage.\u003c\/p\u003e\n\u003cul\u003e\n    \u003cli\u003e\n\u003cb\u003eIntelligent Shift Tuning\u003c\/b\u003e - Gear shifts are optimized for each power level to protect the transmission and increase shift speed while protecting against torque converter and clutch slip.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eAccelerator Pedal Monitoring\u003c\/b\u003e - Rolls in additional power progressively, optimizing for both part-throttle fuel economy and maximum power when you want it.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eActiveSafety\u003c\/b\u003e - Banks combines mechanical fail-safe measures to revert to stock in the event of internal failure while also intelligently adding power based on vehicle operating conditions, such as cold or hot coolant temps or knock from bad fuel.\u003c\/p\u003e\n\u003cul\u003e\n    \u003cli\u003eInternal self-diagnostics checks health of the system 50 times per second\u003c\/li\u003e\n    \u003cli\u003eMonitors MAP and FRP signals for out of range condition (disconnected or short circuit)\u003c\/li\u003e\n    \u003cli\u003eBypass relays smoothly return stock power with no loss of power or \"Limp Mode\"\u003c\/li\u003e\n    \u003cli\u003eActive safety engages if 12-volt power is lost to the Derringer tuner\u003c\/li\u003e\n\u003c\/ul\u003e\u003cb\u003eAdditional Features with iDash\u003c\/b\u003e\u003cul\u003e\n\u003cli\u003eHigh resolution screen with ultra-wide viewing angles\u003c\/li\u003e\n\u003cli\u003eVibrant high-contrast selectable color schemes\u003c\/li\u003e\n\u003cli\u003eHigher speed datalog rate\u003c\/li\u003e\n\u003cli\u003eExpanded memory for nearly unlimited vehicle support\u003c\/li\u003e\n\u003cli\u003eOver-The-Air updates via Bluetooth\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eNOTE: CANNOT SHIP TO CALIFORNIA\u003c\/b\u003e\u003c\/p\u003e","brand":"Banks Power","offers":[{"title":"Default Title","offer_id":52077314408813,"sku":"BAN-67106","price":998.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/BAN-67106_1.jpg?v=1758296411"},{"product_id":"p-edge-98203-back-up-camera-for-cts3-monitors","title":"Edge 98203 Back-Up Camera for CTS3 Monitors","description":"The CTS3 line of products have a built-in video port that allows users to connect Edge's new state-of-the-art back-up camera. The CTS3's high-resolution, 5 inch color screen allows users to see what's going on behind them with the Edge camera connected. The camera mode on the CTS3 automatically engages when the vehicle goes into reverse*. The back-up camera option is a must have for towers and safety-conscious drivers.\u003cbr\u003e\u003cbr\u003e\n\u003cb\u003eIMPORTANT NOTES:\u003c\/b\u003e\n\u003cul\u003e\n    \u003cli\u003eCamera automatically engages on supported vehicles with automatic\n    transmission where we can read the gear parameter.  Not available on all\n    models.\u003c\/li\u003e\n    \u003cli\u003eCTS monitor not included with purchase of camera.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077368770925,"sku":"EDG-98203","price":283.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/4989_117ded4d-db54-43cb-9a2d-326f477c80fd.jpg?v=1752691136"},{"product_id":"p-edge-28862-d2-ampd-20-throttle-booster-with-bluetooth-power-switch-2020-66l-gm-duramax","title":"Edge 28862-D2 AmpD 2.0 Throttle Booster with BlueTooth Power Switch 20-25 GM 6.6L Duramax L5P","description":"\u003cp\u003eDo you ever feel like your L5P GM Duramax has a dead spot in the throttle?  Well, you're right, there is. Any vehicle with a  system in which there is no actual cable attached to your throttle pedal requires a series of wires that send a signal to a computer that relays information to your pump to essentially add fueling.  All of these signals cause a severe delay in throttle response creating this dead spot. The Ampd 2.0 throttle sensitivity booster is the most advanced throttle modification device on the market today. The wireless Bluetooth switch is an industry-exclusive feature and the Ampd 2.0 app provides unparalleled control over your throttle experience. Ampd 2.0 is pre-loaded with 5 preset throttle curves and thousands of custom curve possibilities. You paid for a powerful vehicle and you should have full control over how it drives. Smart phone not included.\u003c\/p\u003e\u003cp\u003e\n\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077389807981,"sku":"EDG-28862-D2","price":286.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/Ampd20_136feae9-ba6a-4eff-b05c-962a1a93f824.png?v=1752691215"},{"product_id":"p-edge-22401-pulsar-v3-tuning-module-20-21-gm-66l-duramax-l5p","title":"Edge 22401 Pulsar V3 Tuning Module 20-23 GM 6.6L Duramax L5P","description":"\u003cp\u003eWake up your 2020+ L5P Duramax with this in-line Pulsar module from the tuning leaders at Edge Products. The Pulsar is the most innovative performance in-line tuner ever to hit the market. This module simple plugs inline to your trucks ECM using factory connectors. No ECM unlocks, no cross shipments, no hassle. The Pulsar supplies instant power, on the fly, with no flash tuning.\u003c\/p\u003e\u003cp\u003e\n\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePower Levels:\u003c\/b\u003e This device comes with 5 different power levels from stock +19hp\/46lb-ft to +90hp\/156lb-ft extreme level. The Pulsar module utilizes the factory cruise control buttons on your steering wheel to set the 5 different power levels on the device. The factory cruise control will work as normal, you can only adjust the power levels when the cruise control function is off. Power levels and other settings are displayed through the speedometer. The view the current power level, simply press the cancel button on your steering keypad, every 10mph marker is one step higher.\u003c\/p\u003e\n\u003cp\u003eBy connecting directly to the trucks PCM, Edge has the ability to control the vehicle to optimize performance gains, throttle response, mileage, tire size, fueling, high-idle, and more.\u003c\/p\u003e\u003cp\u003e\n\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077392986477,"sku":"EDG-22401","price":1126.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/pulsar_1.jpg?v=1772467418"},{"product_id":"p-edge-22601-3-pulsar-insight-cts3-tuning-module-20-21-66l-gm-l5p-duramax","title":"Edge 22601-3 Pulsar \u0026 Insight CTS3 Tuning Module 20-23 6.6L GM L5P Duramax","description":"\u003cp\u003eThe Pulsar V3 + Insight CTS3 for your L5P Duramax delivers a ground pounding 136 horsepower and 291 foot pound of torque increase over your factory tuning, all while having an ease of installation that merely plugs into your factory ECU, eliminating the need to remove and ship your ECM like so many other options on the market today. Stop dealing with wires, expensive ECU swaps, fuel pressure boxes, and other lackluster products. The Edge Pulsar delivers on all fronts witha an ease of install, performance gains, and the only product available that uses steering wheel controls to change power levels while driving, Shift-On-The-Fly. Using live data to change and adapt the Pulsar adjust signals making it the best-in-class winner with features and POWER!\u003c\/p\u003e\n\n\u003cp\u003eThe Pulsar inline module has made waves among truck owners. The industry-exclusive technology, now available via Pulsar, has totally changed the game when it comes to adding performance and keeping the ECU on the truck. No mail-in unlocks, no cross-shipment, or hassle. Pulsar supplies instant power, on the fly, with no flash tuning. Pair the Pulsar V3 with the Insight CTS3 to have the optimal combination of monitoring and power. The Insight provides unparalleled visibility over your vehicles performance and gives you full control over the Pulsar V3. Pulsar V3 + Insight CTS is the optimal combo!\u003c\/p\u003e\n\n\u003cp\u003eThe Pulsar is an in-line computer that connects directly to the vehicle ECM, with no additional wiring harness. By connecting directly to the trucks ECM, Edge has the ability to control the vehicle to optimize performance gains, throttle response, mileage, tire size, fueling, high-idle, and more. To make things even better, the Pulsar offers 5 performance levels that can be switched on-the-fly by using the vehicle cruise control + and buttons on the steering wheel. The active power level (0-5) will be displayed using the speedometer gauge. Simply change performance levels to display what power level or hit cancel on your cruise control to display the current power level.\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077440860525,"sku":"EDG-22601-3","price":1449.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/Pulsar_Edge_1_9bd0441b-354f-45b7-ac4f-6d2a8b79d362.jpg?v=1752691388"},{"product_id":"p-edge-cts3-display-mount-20-22-gm-66l-duramax","title":"Edge CTS3 Display Mount 20-23 GM 6.6L Duramax L5P \/ 20-22 GM 3.0L Duramax LM2","description":"\u003cdiv\u003eThe Edge CTS3 monitor is hands down the most popular powertrain monitoring system, giving you the ability to keep an eye on EGT's, boost pressure, rail pressure, control accessory 12 volt items, and the list goes on. But when it comes time to mount your CTS3, your options are somewhat limited. Sure, the monitor comes with a suction cup mount, but honestly, its not ideal. Another option is you could install a vehicle specific pillar pod, but in many cases, this requires painting the pod, which can be difficult to get to match your factory interior, as well as drilling into your factory pillar, and in some cases, you end up losing your grab handle. All of this has changed with the Edge CTS3 Display Mount that easily installs using a factory mounting bolt and gives a sleek, stylish, out-of-the-way mounting solution for your Chevrolet or GMC truck.\u003c\/div\u003e\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\u003cdiv\u003eThese mounts have been specifically engineered for an OEM look and fitment to place your CTS3 monitor in the perfect viewing position without obstructing your view of the road. Molded and cast from aluminum, the display mounts offer a sturdy mounting location to replace Edge's standard suction cup style mounts. Coated in a sleek matte black finish, they offer a clean look in any interior and are paintable for a customizable look.\u003cbr\u003e\n\u003c\/div\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077471367533,"sku":"EDG-28601","price":72.45,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/28600_1_1ab22dfa-6213-4ad9-aae8-26aee6fc48e3.jpg?v=1752691487"},{"product_id":"p-edge-98108-l5p-duramax-ecm-connector-repair-kit-17-22-gm-66l-duramax-l5p","title":"Edge 98108 L5P Duramax ECM Connector Repair Kit 17-23 GM 6.6L DURAMAX L5P","description":"\u003cp\u003eRepair your damaged ECM connector sliders in your L5P Duramax with this ECM Connector Repair Kit from Edge Products. Overtime, the plastic sliders that lock the ECM connector to the factory ECM become brittle and break. Typically, you would then have to replace the entire connector to ensure a secure connection to your ECM. This simple kit from Edge allows you to replace the broken ECM sliders in a matter of minutes. This process can even be done with the harness still in the vehicle. Fix your ECM connector the correct way with this repair kit from Edge.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077481886061,"sku":"EDG-98108","price":57.85,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/EDG-98108_1.jpg?v=1772469921"},{"product_id":"p-hypertech-730129-in-line-speedometer-calibrator-module-20-22-gm-66l-duramax-l5p","title":"Hypertech 730129 In-Line Speedometer Calibrator Module 20-23 GM 6.6L Duramax L5P","description":"\u003cp\u003eGet accurate speedometer readouts and proper shifts with the Hypertech Speedometer Calibrator for your L5P Duramax.\u003c\/p\u003e\n\u003cp\u003eHypertech's In-Line Speedometer Calibrator Module is a plug-and-play module that corrects the speedometer and odometer for non-stock and\/or gear ratios. With the included USB cable, connect the Hypertech In-Line Speedometer Calibrator to your PC and enter the new tire size and\/or rear gear ratio. There are no limitations to tire height or rear gear ratios. Next, simply disconnect the factory connector to the instrument cluster, snap in the Speedometer Calibrator Module, reconnect the cluster, and you¹re done! In a matter of minutes, you can accurately correct your speedometer and odometer readings. This module is perfect for vehicles with computers that don't allow for tire and gear ratio correction, or to re-calibrate for tire and gear sizes outside the range of programmers.\u003c\/p\u003e","brand":"Hypertech","offers":[{"title":"Default Title","offer_id":52077498827117,"sku":"HYP-730129","price":249.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/730129.jpg?v=1752691569"},{"product_id":"p-edge-98900-replacement-juice-with-attitude-egt-probe","title":"Edge 98900 Replacement Juice With Attitude EGT Probe","description":"\u003cp\u003eEdge Products are some of the highest quality tuning devices on the market. Especially the Juice With Attitude series tuners. In some rare cases over time, EGT probes that come with those tuners can go bad. Not to worry though, Edge Products has the solution. This EGT probe is a direct replacement for all the Edge Juice With Attitude series tuners.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077509476717,"sku":"EDG-98900","price":59.25,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/EDG-98900_1.jpg?v=1772470724"},{"product_id":"p-edge-pulsar-lt-insight-cts3-20-22-gm-66l-l5p-duramax","title":"Edge Pulsar LT In-Line Module + Insight CTS3 20-23 GM 6.6L L5P Duramax","description":"\u003cp\u003eSo you've made some changes to your truck and you need to update your ECM but don't want to void your warranty?  The Pulsar LT + Insight CTS3 is an in-line module and gauge readout for 2020-2023 Chevrolet Silverado and GMC Sierra 2500\/3500 6.6L Duramax that offers complete adjustability of many features, all from your steering wheel controls. Without modifying your truck's ECM, Pulsar LT offers you the ability to adjust throttle response, tire size, gear ratio, TPMS, and your top speed limiter. Pulsar LT for Duramax can also be used to command a manual DPF regen cycle, automatic transmission relearn, clear DTC's and high idle the engine. It connects directly to the vehicle computer system, making installation a breeze and leaving your factory warranty intact.\u003c\/p\u003e\n\u003cp\u003eStepping it up one notch, this kit also includes our industry leading Insight CTS3 monitor for all the live data you could ever ask for. The Insight is the #1 preferred digital gauge monitor in the market today, used by daily drivers and enthusiasts everywhere. The Insight is the most comprehensive, state-of-the-art, multi-gauge touch-screen display on the market. It is an instantaneous and inexpensive alternative to bulky, analog gauges that would otherwise cost hundreds of dollars and take hours to install. This is the perfect tool for those who want to monitor their vehicle's performance and prefer not to program their vehicle. It can also be intelligently configured to provide audible and visual alerts to help you protect your vehicle.\u003c\/p\u003e\n\u003cp\u003eVehicle specific A-Pillar Display Mount also included for a sleek more permanent way to mount the CTS3 in the cab of your truck. These mounts offer an OE look, while keeping the monitor within easy reach without obstructing your view of the road.\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077511115117,"sku":"EDG-23411-3","price":1177.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/23410-3-1_33069d98-ca3d-42ca-ba43-8808645b2764.jpg?v=1752691601"},{"product_id":"p-edge-evoht2-tuner-with-ecmtcm-unlock-20-22-gm-66l-duramax-l5p","title":"Edge EvoHT2 Tuner With ECM\/TCM Unlock 20-23 GM 6.6L Duramax L5P","description":"\u003cp\u003eUnlock the power potential of your L5P Duramax with a simple to use tuner that gives your Duramax up to 125 HP and 275 LB-FT along with TCM or \"Transmission Control Module\" tuning. The Edge EvoHT2! This is a tuning option with efficient and easy to use technology, a color screen with great visuals, and four levels of pre-loaded tuning. This device will also give you the ability to calibrate for larger tires, idle up feature, command manual DPF regeneration, and read and clear DTC's. The EvoHT2 also offers an industry first 'Remember Last Setting' feature that allows your truck to remember your Tow\/Haul, Grade Braking, and Exhaust Brake settings every time you start your truck!\u003c\/p\u003e\n\u003cp\u003eEdge's revolutionary TCM tuning allows you to optimize the 10-speed Allison for improved shift points, better clutch holding capacity from increased line pressure, and converter lockup. This allows your Allison to handle everything you can throw at it whether your daily driving, towing, or having fun on the streets. Who knew the 10-speed Allison could get even better!\u003c\/p\u003e\n\u003cp\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-weight: bold;\"\u003eREVOLUTIONARY ECM\/TCM UNLOCKING\u003c\/span\u003e\u003cbr\u003e\n\u003c\/p\u003e\u003cp\u003eIn the past, unlocking your L5P's ECM required you to send in your L5P's complete ECM into Edge so they could perform the unlock process. Not any more! Edge has developed a revolutionary Locksmith device for a plug and play ECM\/TCM unlock. The EvoHT2 now offers complete ECM\/TCM unlocking without touching the modules. No cores to deal with. No finicky harnesses to disconnect. A PC and Edge's downloadable Update Agent software will be required in order to complete the unlocking process. This device will only be able to unlock and tune one vehicle. Once the modules are unlocked and flashed, you will be able to return the vehicle back to stock but the unlock process cannot be reversed. When the VIN lock and ECM\/TCM unlock has been completed, the device will not be eligible for return.\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077593035117,"sku":"EDG-26401","price":499.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/26401.png?v=1752691868"},{"product_id":"p-bully-dog-thruster-throttle-booster-07-18-dodgeram-59l67l-cummins-08-20-gm-66l-duramax","title":"Bully Dog Thruster Throttle Booster 07-21 Dodge\/Ram 5.9L\/6.7L Cummins 08-22 GM 6.6L Duramax","description":"\u003cp\u003eAre you looking to make your throttle more responsive with better vehicle acceleration? You can have both with Bully Dog’s Thruster Throttle Booster. This device will reduce lag time making it easy to jump into the passing lane, hit the racetrack, or give you the boost you need for those off-road trips. To make it even better, it’s easy to install inline between your vehicle’s pedal position sensor and the vehicle harness. Adjust on the fly and really feel the change as you drive. With it's waterproof design, it's well suited for off-roading, and it'll give your vehicle just the boost it needs. 50 State legal.\u003cbr\u003e\u003c\/p\u003e","brand":"Bully Dog","offers":[{"title":"2007-2021 Ram 5.9L|6.7L Cummins","offer_id":52077653066093,"sku":"BUL-49002EO","price":299.0,"currency_code":"USD","in_stock":true},{"title":"2008-2022 GM 6.6L Duramax","offer_id":52077653098861,"sku":"BUL-49003EO","price":299.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/Thruster_970x970-1.jpg?v=1752692040"},{"product_id":"p-banks-mounting-bracket-for-banks-sensor-modules-and-derringer","title":"Banks Mounting Bracket for Banks Sensor Modules and Derringer","description":"\u003cp\u003e\n    Bracket kit for Banks Derringer Tuners or Sensor Modules. Use it to securely mount one or more modules to a flat surface.\n\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eRECOMMENDED NUMBER OF BRACKETS:\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cstyle\u003e\n    .table-d45fg6d4fg658dfg {\n        border-collapse: collapse;\n        width: 100%;\n    }\n\n    .table-d45fg6d4fg658dfg td,\n    .table-d45fg6d4fg658dfg th {\n        border: 1px solid #ddd;\n        padding: 12px 15px;\n    }\n\n    .table-d45fg6d4fg658dfg tr:nth-child(odd) {\n        background-color: #f2f2f2;\n    }\n\n    .table-d45fg6d4fg658dfg th {\n        text-align: left;\n        background-color: rgb(105, 105, 105);\n        color: white;\n    }\n\u003c\/style\u003e\n\n\u003cdiv style=\"overflow: auto;\"\u003e\n    \u003ctable class=\"table-d45fg6d4fg658dfg\"\u003e\n        \u003ctbody\u003e\n\u003ctr\u003e\n            \u003cth\u003eModules\u003c\/th\u003e\n            \u003cth\u003eBrackets\u003c\/th\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003e1-2 modules\u003c\/td\u003e\n            \u003ctd\u003e1 bracket\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003e3-4 modules\u003c\/td\u003e\n            \u003ctd\u003e2 brackets\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003e4-5 modules\u003c\/td\u003e\n            \u003ctd\u003e3 brackets\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003e5+ modules\u003c\/td\u003e\n            \u003ctd\u003e4 brackets\u003c\/td\u003e\n        \u003c\/tr\u003e\n    \u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e","brand":"Banks Power","offers":[{"title":"Default Title","offer_id":52077689405805,"sku":"BAN-66423","price":20.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/66423_Banks-sensor-mount_1-5231.jpg?v=1752692121"},{"product_id":"p-banks-idash-stealth-pod-gauge-mounts-gm-2500-3500","title":"Banks iDash Stealth Pod Gauge Mounts 19-21 GM 1500 | 20-23 GM 2500HD\/3500","description":"With a simple clean look, iDash® Stealth Pods are the perfect mount solution for 52mm iDash® gauges. They are specifically designed to endure extreme conditions, including heat, cold, and UV exposure, throughout the lifespan of your vehicle. These pods are securely affixed to the A-pillar of your truck at an angle that optimizes gauge visibility and ergonomics. Proudly made in the USA from industrial-grade polymer, iDash Stealth Pods can be installed in minutes and are built to last. Each Stealth Pod comes in a natural black finish, but you have the option to paint them to match your vehicle's interior.\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan style=\"font-weight: bold;\"\u003eIMPORTANT NOTES: \u003c\/span\u003e\u003c\/div\u003e\u003cdiv\u003e\u003cul\u003e\n\u003cli\u003eBanks Stealth Pods are designed specifically for the low depth of their iDash® Gauge\u003c\/li\u003e\n\u003cli\u003eThey are NOT compatible with mechanical or deep-set gauges\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/div\u003e\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003ciframe style=\"width: 100%; height: 300px;\" loading=\"lazy\" src=\"https:\/\/player.vimeo.com\/video\/762828434\" frameborder=\"0\" allowfullscreen=\"\"\u003e\n\u003c\/iframe\u003e","brand":"Banks Power","offers":[{"title":"Single Pod","offer_id":52077719650669,"sku":"BAN-63359","price":109.0,"currency_code":"USD","in_stock":true},{"title":"Dual Pod","offer_id":52077719683437,"sku":"BAN-63362","price":129.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/5_63359_63362_Combo-Shot-3682_4e3ed177-edaf-40da-8260-03521ca4a889.jpg?v=1752692201"},{"product_id":"p-banks-idash-stealth-pod-gauge-mounts-23-24-gm-15002500hd3500","title":"Banks iDash Stealth Pod Gauge Mounts 23-25 GM 1500\/2500HD\/3500","description":"With a simple clean look, iDash® Stealth Pods are the perfect mount solution for 52mm iDash® gauges. They are specifically designed to endure extreme conditions, including heat, cold, and UV exposure, throughout the lifespan of your vehicle. These pods are securely affixed to the A-pillar of your truck at an angle that optimizes gauge visibility and ergonomics. Proudly made in the USA from industrial-grade polymer, iDash Stealth Pods can be installed in minutes and are built to last. Each Stealth Pod comes in a natural black finish, but you have the option to paint them to match your vehicle's interior.\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003cdiv\u003e\u003cspan style=\"font-weight: bold;\"\u003eIMPORTANT NOTES: \u003c\/span\u003e\u003c\/div\u003e\u003cdiv\u003e\u003cul\u003e\n\u003cli\u003eBanks Stealth Pods are designed specifically for the low depth of their iDash® Gauge\u003c\/li\u003e\n\u003cli\u003eThey are NOT compatible with mechanical or deep-set gauges\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/div\u003e\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003ciframe style=\"width: 100%; height: 300px;\" loading=\"lazy\" src=\"https:\/\/player.vimeo.com\/video\/866184393\" frameborder=\"0\" allowfullscreen=\"\"\u003e\n\u003c\/iframe\u003e","brand":"Banks Power","offers":[{"title":"Single Pod","offer_id":52077719945581,"sku":"BAN-63369","price":109.0,"currency_code":"USD","in_stock":true},{"title":"Dual Pod","offer_id":52077719978349,"sku":"BAN-63370","price":129.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/63369-70-Both-2-7612.jpg?v=1752692202"},{"product_id":"p-edge-evolution-cts3-tuner-17-23-gm-66l-duramax-l5p","title":"Edge Evolution CTS3 Tuner 17-23 GM 6.6L Duramax L5P","description":"\u003cp\u003eThe Edge Evolution CTS3 Tuner unlocks the power potential of your L5P Duramax Diesel engine. The CTS3 is the undefeated champion when it comes to monitor displays, featuring a slim case design and a 5 full-color capacitive edge-to-edge display with true swipe screen technology. Not only is the display sharper, but the higher resolution screen delivers a tremendous pixel ratio and top-notch graphics. New screen layouts, faster processing speeds, and WiFi update capability are just a few things that set the Evolution CTS3 apart from all other competitors.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e\u003cp\u003eECM\/TCM Unlocking, tuning and monitoring is now possible, right from the cab of your L5P with the Evolution CTS3. After the massive success of Edge's EvoHT2 and Locksmith device released in August of 2022, Edge now offers the same class leading tuning and first of it’s kind ECM\/TCM unlocking technology with the industry’s leading touchscreen monitoring device, the CTS3. Using revolutionary Locksmith device and included unlock cable(s), the Evolution CTS3 now offers complete ECM unlocking for 2017-2019 models and ECM\/TCM control in 2020-2023 platforms.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e\u003cp\u003eThis is a complete all-in-one device, saving you time and money over the competitive offerings in the space when it comes time to modify your late model GM diesel truck. Evolution CTS3 offers massive power gains up to 150hp with improved throttle response, quicker turbo spool-up, better fuel economy and user control over their driving experience, don’t wait and unlock your L5P’s max potential with Evolution CTS3 today!\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"2017-2019","offer_id":52077746094445,"sku":"EDG-85400-262","price":870.95,"currency_code":"USD","in_stock":true},{"title":"2020-2023","offer_id":52077746127213,"sku":"EDG-85400-261","price":1075.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/e8c198a7101c222df8f90184a169b3-3590_2.jpg?v=1752692298"},{"product_id":"p-edge-pulsar-md-tuning-module-chevrolet-l5d-duramax","title":"Edge Pulsar MD Tuning Module 19-23 Chevrolet 4500\/5500\/6500 6.6L Duramax L5D","description":"\u003cdiv\u003eYou put in 100% when you go to work, leaving nothing on the table.  You should be able to expect the same dedication out of your truck. The sizeable 4500\/5500\/6500 work trucks offer versatility, but struggle under their hefty weight with the factory power and torque ratings provided by the L5D Duramax.\u003cbr\u003e\n\u003c\/div\u003e\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\u003cdiv\u003eThe Pulsar MD for Chevrolet Medium Duty offers easy plug and play, emissions friendly performance to put a bee in the bonnet of your medium-duty work horse.  Stop driving that lethargic, underpowered L5D Duramax and start enjoying your driving experience during your day to day.  Your time is valuable, why deal with time consuming wiring, unsightly installation fails, expensive ECM unlocks, unnecessary ECM swaps or ECM flashing.  Pulsars easy 10 minute installation serves up to 135hp extra horsepower and feature controls at your fingertips! \u003cbr\u003e\n\u003c\/div\u003e\u003cbr\u003eWith Pulsar, you get on-the-fly power control with five performance settings to meet just about any situation. From heavy towing to your daily drive and commuting duties, Pulsar MD will completely change your driving experience. Use the steering wheel controls to command a manual DPF regeneration cycle, calibrate your speedometer for larger tires, and even clear DTC’s that try to complicate your day. Pulsar MD is the most innovative module for Medium Duty Duramax trucks on the market today. The device also offers easy engine Hi-Idle control for better in-field performance on the job site. Using live data to change and adapt, the Pulsar is a best-in-class winner for power and feature control, with built-in safety backdowns to ensure that your Medium Duty truck keeps serving you loyally on the job for years to come!\u003cbr\u003e\u003cp\u003e\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077783777645,"sku":"EDG-22403","price":1126.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/PulsarL5D_2.jpg?v=1752692422"},{"product_id":"p-edge-ez-module-2024-gm-66l-duramax","title":"EDGE EZ Performance Tuning Module 24-26 GM 6.6L Duramax L5P","description":"\u003cp\u003eNeed extra performance that is easy to install on your L5P 6.6L Duramax and won't interfere with emissions? Edge Products has developed the EZ Module with you in mind. Using breakthrough inline module tech,  Edge has created new calibrations that allow for more torque, more power, and a pedal that feels right with a safe and easy install process. Download the intuitive smartphone app to control on-the-fly tuning adjustments for the five unique calibrations. On top of that, you can combine power levels with pedal settings to create control of the throttle feel and eliminate pedal drag.\u003c\/p\u003e\n\u003cp\u003eThe EZ Module interacts with signals for specific sensors in your pickup so that you can have your truck adjust to your needs, not the other way around. Using changes to your rail pressure curve, monitoring vital data, and adjusting mass airflow you can get peak gains of 63hp\/140tq without sacrificing part longevity or any emissions requirements. Worried that this added horsepower comes with a lot of extra and damaging heat? Edge's EZ Module has a built-in Temperature Protection system to make sure you're always within operating heat temperatures no matter your torque or horsepower. Edge tests all of its products thoroughly to make sure this is the solution you are looking for because just like you they are a bunch of diesel guys.\u003c\/p\u003e\n\u003cp\u003ePlanning on towing? EZ Module helps with that as well with improved fuel economy and better towing performance. Whether you just drive your truck for the morning commute or weekend off-road, the Edge EZ Module is the affordable and easy way to get the most out of your Duramax.\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077831553389,"sku":"EDG-20202","price":562.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/EDG-20202_1_2.jpg?v=1752692575"},{"product_id":"p-edge-ez-insight-cts3-kit-2024-chevroletgmc-l5p-66l-duramax","title":"EDGE EZ Performance Tuning Module + Insight CTS3 Kit 24-25 GM 6.6L Duramax L5P","description":"\u003cp\u003eGet extra performance and a state-of-the-art digital gauge monitor together in one package. Edge Products has taken the EZ Module and combined it with their Insight CTS3 multi-gauge monitor for the perfect combination of performance and intelligence. Using breakthrough inline module tech,  Edge's EZ Module created new calibrations that allow for more torque, more power, and a pedal that feels right with a safe and easy install process. Download the intuitive smartphone app to control on-the-fly tuning adjustments for the five unique calibrations. On top of that, you can combine power levels with pedal settings to create control of the throttle feel and eliminate pedal drag.\u003c\/p\u003e\n\u003cp\u003eThe EZ Module interacts with signals for specific sensors in your pickup so that you can have your truck adjust to your needs, not the other way around. Using changes to your rail pressure curve, monitoring vital data, and adjusting mass airflow you can get peak gains of 63hp\/140tq without sacrificing part longevity or any emissions requirements. Worried that this added horsepower comes with a lot of extra and damaging heat? Edge's EZ Module has a built-in Temperature Protection system to make sure you're always within operating heat temperatures no matter your torque or horsepower. Edge tests all of its products thoroughly to make sure this is the solution you are looking for because just like you they are a bunch of diesel guys.\u003c\/p\u003e\n\u003cp\u003ePlanning on towing? EZ Module helps with that as well with improved fuel economy and better towing performance. Whether you just drive your truck for the morning commute or weekend off-road, the Edge EZ Module is the affordable and easy way to get the most out of your Duramax.\u003c\/p\u003e\n\u003cp\u003eYou need power but how about information on the fly? The Insight digital gauge monitor is a customizable solution that gives you all the parameters like EGT, regen cycles, trans temp, boost, RPM, and dozens more in an easy-to-read display. Create audible and visual alerts so that you can make sure you protect your vehicle while adjusting performance. Gain the abillity to read and clear trouble codes and perform a manual DPF Regeneration cycle. Insight CTS3 paired with the EZ Module gives you exactly what you need: performance with total control.\u003cbr\u003e\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077831389549,"sku":"EDG-20202-3","price":999.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/EDG-20202-3_1_2.jpg?v=1752692575"},{"product_id":"p-edge-tuning-device-suction-mount","title":"EDGE Universal Tuning Device Suction Cup Mount","description":"\u003cdiv\u003eSecure your in-cab tuner with ease using the EDGE Tuning Device Suction Cup Mount, a reliable replacement mount designed to keep your tuning and monitoring device firmly in place. With its strong suction mechanism, this mount attaches effortlessly to your windshield, offering stability and flexibility without requiring any modifications to your vehicle.\u003c\/div\u003e\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\u003cdiv\u003eThis universal mount is compatible with a wide range of devices, including Edge CS2, CTS2, CTS3, Insight, Evolution, and Juice, as well as DiabloSport Trinity, MX, and Superchips Dashpaq, Dashpaq+, TrailDash2, and TrailDash3. It's also built to fit seamlessly with Holley Tuning Group in-cab devices, making it the ultimate solution for versatile, hassle-free installation. Whether you're navigating trails, monitoring performance, or dialing in your custom tune, the EDGE Suction Cup Mount keeps your device within reach and ready to perform. Its sleek design and strong hold ensure uninterrupted access to your critical information, even on the roughest roads. Upgrade your setup with the EDGE Tuning Device Suction Cup Mount, a solid, universal solution for drivers who demand both functionality and flexibility.\u003c\/div\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077908230509,"sku":"EDG-98110","price":17.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/98110-1.jpg?v=1752692849"},{"product_id":"p-edge-insight-cts3-monitor-custom-tuning-device","title":"EDGE Insight+ CTS3 Monitor \u0026 Custom Tuning Device","description":"\u003cdiv\u003eThe EDGE Insight+ CTS3 Monitor \u0026amp; Custom Tuning Device is the ultimate performance and monitoring solution for your truck, delivering all the functionality of the industry leading Insight CTS3 with the added capability of custom tuning.\u003c\/div\u003e\n\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003cdiv\u003eWhether you’re looking to keep a close eye on vital engine parameters or load custom tunes for optimal power and efficiency, the Insight-Plus has you covered. Pre-loaded with a custom tune license (1994-2007 Ford Powerstroke or 2004.5-2023 L5P \u0026amp; LLY Duramax Only), this device allows you to read your truck’s ECM and create a backup file that can be sent to your preferred \u003cspan style=\"font-weight: bold;\"\u003eEdge approved custom calibration shop\u003c\/span\u003e. Once your tuner customizes the files for your truck, you can easily upload them via your PC and flash them to your vehicle in just a few simple steps, this tuner is built to grow with your needs.\u003c\/div\u003e\n\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003cdiv\u003eBeyond tuning, the Insight+ provides real-time monitoring of key vehicle parameters like EGT, regen cycles, transmission temperature, boost, RPM, and more, all displayed on a crisp, easy-to-navigate touchscreen. Swipe between customizable layouts for towing, performance, and economy, or take advantage of built-in performance meters to track 0-60 and quarter-mile times. An advanced data logger lets you export driving data, while integrated diagnostics allow you to read and clear DTC codes with ease. Installation is simple, just plug it into the OBDII port, no wiring required. The Insight+ also features Wi-Fi updateability, manual and mobile DPF regeneration capabilities for select diesel applications, and compatibility with Edge’s EAS (Expandable Accessory System) for adding sensors to monitor even more parameters. For those who like to keep things clean and factory looking cabins, it can also control 12V accessories like auxiliary lighting directly through the touchscreen, eliminating the need for extra switches cluttering your dash.\u003c\/div\u003e\n\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003cdiv\u003eSleek, powerful, and packed with features, the EDGE Insight+ CTS3 is more than just a digital gauge, it’s your key to unlocking your truck’s full potential while keeping it running safe and strong. Whether you're a daily driver, a heavy hauler, or an enthusiast pushing the limits, this is the performance tool you’ve been waiting for.\u003c\/div\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077947060589,"sku":"EDG-84140","price":599.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/84140-1-3_2.jpg?v=1752692967"},{"product_id":"p-edge-insight-cts3-monitor-custom-tuning-device-ecutcm-unlock-kit-20-23-gm-66l-duramax-l5p","title":"EDGE Insight+ CTS3 Monitor \u0026 Custom Tuning Device \u0026 ECU\/TCM Unlock Kit 20-23 GM 6.6L Duramax L5P","description":"\u003cdiv\u003eThe EDGE Insight+ CTS3 Monitor \u0026amp; Custom Tuning Device for the 2020-2023 GM 6.6L Duramax L5P is the \nultimate performance and monitoring solution for your truck, delivering \nall the functionality of the industry leading Insight CTS3 with the \nadded capability of custom tuning.\u003c\/div\u003e\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\u003cdiv\u003eThis kit is \nbuilt specific for 2017-2019 GM L5P Duramax applications and includes \nall required hardware to be able to monitor and unlock\/flash ECM\/TCM third \nparty calibrations into the truck. Kit includes our revolutionary \nLocksmith unlock tool, ECM unlock harness, and our cast A-pillar mount \nfor an OEM like fit of the Insight+ monitor in the cab. Whether \nyou’re looking to keep a close eye on vital engine parameters or load \ncustom tunes for optimal power and efficiency, the Insight-Plus has you \ncovered. Pre-loaded with a custom tune license, this device allows you \nto read your truck’s ECM\/TCM and create a backup file that can be sent \nto your preferred \u003cspan style=\"font-weight: bold;\"\u003eEdge approved custom calibration shop\u003c\/span\u003e.\n Once your tuner customizes the files for your truck, you can easily \nupload them via your PC and flash them to your vehicle in just a few \nsimple steps, this tuner is built to grow with your needs.\u003c\/div\u003e\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\u003cdiv\u003eBeyond\n tuning, the Insight+ provides real-time monitoring of key vehicle \nparameters like EGT, regen cycles, transmission temperature, boost, RPM,\n and more, all displayed on a crisp, easy-to-navigate touchscreen. Swipe\n between customizable layouts for towing, performance, and economy, or \ntake advantage of built-in performance meters to track 0-60 and \nquarter-mile times. An advanced data logger lets you export driving \ndata, while integrated diagnostics allow you to read and clear DTC codes\n with ease. Installation is simple, just plug it into the OBDII port, no\n wiring required. The Insight+ also features Wi-Fi updateability, manual\n and mobile DPF regeneration capabilities for select diesel \napplications, and compatibility with Edge’s EAS (Expandable Accessory \nSystem) for adding sensors to monitor even more parameters. For those \nwho like to keep things clean and factory looking cabins, it can also \ncontrol 12V accessories like auxiliary lighting directly through the \ntouchscreen, eliminating the need for extra switches cluttering your \ndash.\u003c\/div\u003e\u003cdiv\u003e\u003cbr\u003e\u003c\/div\u003e\u003cdiv\u003eSleek, powerful, and packed with \nfeatures, the EDGE Insight+ CTS3 is more than just a digital gauge, it’s\n your key to unlocking your truck’s full potential while keeping it \nrunning safe and strong. Whether you're a daily driver, a heavy hauler, \nor an enthusiast pushing the limits, this is the performance tool you’ve\n been waiting for.\u003c\/div\u003e","brand":"Edge Products","offers":[{"title":"Default Title","offer_id":52077947093357,"sku":"EDG-84140-1","price":972.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/files\/84140-1-1.jpg?v=1752692967"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0892\/2487\/2301\/collections\/CTS3_3screens11-2_713x960_bb9c2707-6660-400a-9905-1ed242e87766.jpg?v=1772568224","url":"https:\/\/dieselpowerproducts.com\/collections\/c-2020-gm-duramax-programmers.oembed","provider":"Diesel Power Products","version":"1.0","type":"link"}